Stop Water – This is a common problem that has a very simple solution. Water can seep through foundation walls leaving stains on the surface or even puddles on the floor. Stop the water for good with Epoxy Waterproofer! We have been making this 2 part waterproofing epoxy for 40 years and have stopped thousands of gallons of water from damaging basements.
It’s Safe and Easy to Apply
No solvents are added to this 100% epoxy, there is no obnoxious smells or toxic fumes. Application is as easy as mixing the part B into the part A and then applying with a brush or roller over the affected areas. Add color packs if desired in order to tint the epoxy to easier blend or hide repairs.
Epoxy Waterproofer withstands hydro-static pressure and will not peel or flake off of the surface.
Traditionally, basement waterproofing always involved excavating the foundation; a costly undertaking indeed. Today there are a number of ways to fix wet basements from within the basement itself – a much less expensive (and less destructive) proposition.
There are many ways to stop ground water from entering a finished basement through a leaking crack, but none of them are as simple as using our Epoxy Waterproofer. Just brush it over a crack, allow it to set and you’re done, no chipping and no patching. Wide cracks can be sealed by mixing clean silica sand into the epoxy to make an epoxy mortar that will stay in place while it cures. Watch our video to see how simple it is.
Epoxy waterproofer is a specially formulated heavy bodied thermo setting Epoxy resin. When mixed with it’s activator it becomes self curing and hardens to a ceramic like, non porous, impermeable clear film. If you would prefer a color Epoxy Water proofer is also available with
color packs offering up to 35 different color combinations.
Since it is 100% solids, it can be applied from a thin brush application to 1/16th or 1/8th inch thick claddding that can withstand tons of hydrostatic pressure.
Epoxy Waterproofer is designed to be a heavy duty waterproof protective coating that seals porous surfaces, fine cracks and voids. (Sand may be added for wide crack filler)
It is also highly suitable for coating and lining tanks, submerged concrete units, troughs, pipe, utility ducts, etc. Also excellent to seal off leaks in below grade basement wall areas.
Epoxy Waterproofer is also used to waterproof Koi Fish ponds, Waterfalls, Fountains, bird Baths, Water Cisterns for potable water. Coverage rate for qt. units 25 sq. ft .
Available Color Chart
The colors shown here are a digital representation of the colors available. Because of variances in color representation from one monitor to the next they should not be relied on if color matching is required in your project.
Many leaking fish ponds are constructed of cement plaster over concrete blocks. From thermal movement these ponds will sometimes develop hairline cracks which will then leak water out. Many people will chip the crack out and do the usual hydraulic cement patch, and within a short period of time it cracks again. The Chargar Corporation has developed a thick 100% epoxy coating that can bridge the crack, waterproof it and prevent further cracking from movement. The Epoxy Waterproofer can be brushed applied over the crack forming a 15 mil impervious film. It has slight expansion and contraction ability. It comes in clear or colors.
Won’t Harm the Fish
Since Epoxy Waterproofer is 100% solids it becomes completely inert once it has fully cured. This means that it will not leach any harmful chemicals and will not hurt the livestock. It will not cause any algae issues by leaching nitrates or phosphates. Customers have used this epoxy to seal ponds for over 30 years with no ill effects.
Ponds aren’t the only use for Epoxy Waterproofer. It can be used to build and seal water fountains of any size. Since it is safe to use with potable water, many customers in the agricultural industry have used Epoxy Waterproofer to seal animal drinking troughs and and cisterns.
For more information call 800-922-4623 or email firstname.lastname@example.org
Enviro-Shield 40WB is a water based, VOC compliant, high performance, clear, penetrating water repellent sealer. It is designed to provide long term protection for brick, blocks, Jersey barriers, vertical or horizontal concrete and natural stones and other porous surfaces.
Enviro-Shield 40WB repels water on masonry surfaces for up to 10 years and can be sprayed with a low pressure sprayer, allowing it to thoroughly soak the surface up 1/2″ deep.
Enviro-Shield is easy to use. Overspray can be washed off with soap and water. Sprayers and tools can be washed with soap and water.
Enviro-shield is available in formulas of 20% solids and 40% solids. Enviro-shield is an excellent cold weather water repellent since it will not freeze.