Stop Water – This is a common problem that has a very simple solution. Water can seep through foundation walls leaving stains on the surface or even puddles on the floor. Stop the water for good with Epoxy Waterproofer! We have been making this 2 part waterproofing epoxy for 40 years and have stopped thousands of gallons of water from damaging basements.
It’s Safe and Easy to Apply
No solvents are added to this 100% epoxy, there is no obnoxious smells or toxic fumes. Application is as easy as mixing the part B into the part A and then applying with a brush or roller over the affected areas. Add color packs if desired in order to tint the epoxy to easier blend or hide repairs.
Epoxy Waterproofer withstands hydro-static pressure and will not peel or flake off of the surface.
Epoxy Waterproofer contains 100% solids and is applied from a thin brush application up to a 1/8th inch thick cladding capable of withstanding hydrostatic pressure and stopping radon gas migration in a leaking basement. Cracks and patches can be repaired and made waterproof by adding clean silica sand to Epoxy Waterproofer.
Know the difference between “sealed” and “waterproof”. Epoxy Waterproofer is a specially formulated, heavy bodied, thermo setting, self curing epoxy that hardens to a ceramic like, non-porous, clear, impermeable and waterproof film. This is a 2 part 100% solids epoxy that cures clear or can be pigments to a variety of colors by adding a color pack. Use on interior/exterior foundations, precast concrete tanks, stone, potable water tanks, ponds, waterfalls, pools etc.
Epoxy Waterproofer has been brush applied over a crack which has been filled with hydraulic cement. If the crack opening is larger than 1/8″ pack with hydraulic cement. Allow hydraulic cement to set for 15 minutes. Mix a small amount of Epoxy Waterproofer, enough to cover the hydraulic cement filled crack. Brush apply a liberal amount over the crack with a minimum of 1/2″ overlapping the crack. Once the Epoxy Waterproofer has set 24 hrs this crack is finished and will withstand tons of water without leaking. Color packs can be added to the clear material in order to better match the surrounding area.
Traditionally, basement waterproofing always involved excavating the foundation; a costly undertaking indeed. Today there are a number of ways to fix wet basements from within the basement itself – a much less expensive (and less destructive) proposition.
There are many ways to stop ground water from entering a finished basement through a leaking crack, but none of them are as simple as using our Epoxy Waterproofer. Just brush it over a crack, allow it to set and you’re done, no chipping and no patching. Wide cracks can be sealed by mixing clean silica sand into the epoxy to make an epoxy mortar that will stay in place while it cures. Watch our video to see how simple it is.
Epoxy waterproofer is a specially formulated heavy bodied thermo setting Epoxy resin. When mixed with it’s activator it becomes self curing and hardens to a ceramic like, non porous, impermeable clear film. If you would prefer a color Epoxy Water proofer is also available with
color packs offering up to 35 different color combinations.
Since it is 100% solids, it can be applied from a thin brush application to 1/16th or 1/8th inch thick claddding that can withstand tons of hydrostatic pressure.
Epoxy Waterproofer is designed to be a heavy duty waterproof protective coating that seals porous surfaces, fine cracks and voids. (Sand may be added for wide crack filler)
It is also highly suitable for coating and lining tanks, submerged concrete units, troughs, pipe, utility ducts, etc. Also excellent to seal off leaks in below grade basement wall areas.
Epoxy Waterproofer is also used to waterproof Koi Fish ponds, Waterfalls, Fountains, bird Baths, Water Cisterns for potable water. Coverage rate for qt. units 25 sq. ft .
Available Color Chart
The colors shown here are a digital representation of the colors available. Because of variances in color representation from one monitor to the next they should not be relied on if color matching is required in your project.
Enviro-Shield 40WB is a water based, VOC compliant, high performance, clear, penetrating water repellent sealer. It is designed to provide long term protection for brick, blocks, Jersey barriers, vertical or horizontal concrete and natural stones and other porous surfaces.
Enviro-Shield 40WB repels water on masonry surfaces for up to 10 years and can be sprayed with a low pressure sprayer, allowing it to thoroughly soak the surface up 1/2″ deep.
Enviro-Shield is easy to use. Overspray can be washed off with soap and water. Sprayers and tools can be washed with soap and water.
Enviro-shield is available in formulas of 20% solids and 40% solids. Enviro-shield is an excellent cold weather water repellent since it will not freeze.