The Energex Finish Coats are durable coatings which provide surface color and textre for the Energex Stucco System. These finishes can be applied as well over exterior masonry, stucco, precast or cast-in-place concrete, cement block, and other approved substrates. These finishes are also suitable for interior applications. Choose from a variety of colors and texures.
Use a stainless steel trowel to apply ENERMIX DRY Base Coat to the surface in a uniform thickness as recommended for the type of reinforcing mesh being installed. Immediately, place the reinforcing mesh against the wet Base Coat. The surface of the Base Coat is smoothed with a trowel until the reinforcing mesh is fully embedded. The pattern of the mesh must not be visible.
Enviro-Shield 40% is an alcohol based, VOC compliant, high performance, clear, penetrating water repellent sealer.
It is designed to provide long term protection for brick, blocks, Jersey barriers, vertical or horizontal concrete and natural stones and other porous surfaces.
Enviro-Shield 40% repels water on masonry surfaces for up to 10 years and can be sprayed with a low pressure sprayer, allowing it to thoroughly soak the surface up 1/2″ deep. Over spray can be washed off with soap and water. Sprayers and tools can be washed with soap and water.
Enviro-Shield 40% is available in formulas of 20% solids and 40% solids. Enviro-shield is an excellent cold weather water repellent since it will not freeze.
Enviro-Shield 40% passes the NHCRP244 series test,full data on record.
Klere-Treat WB is a masonry water repellent based on a silane and siloxane. Under the influence of atmospheric humidity, it chemically reacts with and bonds to masonry, forming a highly effective poly-siloxane repellent. It is highly alkaline resistant and designed for use on brick, concrete block, precast concrete, stucco, limestone, fieldstone and many other natural stones.
Kleare-Treat WB provides superior protection against moisture penetration, thereby preventing the deleterious effects of efflorescence. The deep penetrating application retains it’s natural appearance with no surface build up or darkening effects. The masonry remains completely breathable.
Klere-Treat WB can also be applied to parking garages and flat concrete or masonry surfaces to reduce attack from deicing salts.
The advantages of Klere-Treat WB include:
- Deep Penetration into surfaces
- Non-film forming
- Does non contain wax, gum resins, silicas or silicones
- Unlike many water repellents Klere-Treat WB does not break down due to alkali in masonry.
- Resists water penetration for 10 years
- Highly resistant to acid rain
- Safe water based formula, water cleanup
- No toxic fumes or vapors
Enviro-Shield 40WB is a water based, VOC compliant, high performance, clear, penetrating water repellent sealer. It is designed to provide long term protection for brick, blocks, Jersey barriers, vertical or horizontal concrete and natural stones and other porous surfaces.
Enviro-Shield 40WB repels water on masonry surfaces for up to 10 years and can be sprayed with a low pressure sprayer, allowing it to thoroughly soak the surface up 1/2″ deep.
Enviro-Shield is easy to use. Overspray can be washed off with soap and water. Sprayers and tools can be washed with soap and water.
Enviro-shield is available in formulas of 20% solids and 40% solids. Enviro-shield is an excellent cold weather water repellent since it will not freeze.
AC-3 is one of the safest and most effective all purpose acid cleaners on the market.
Compounded with a comparatively safe acid, strong detergent and solvents to provide a fast 3 way cleaning action.
Accidental splashing will not cause skin burns or discomfort, nor will it harmfully effect most masonry surfaces.
AC-3 Acid Cleaner has a pleasant clean odor and dispels no harmful or corrosive fumes.
AC-3 three way cleaning action will penetrate deeply into the surface and will dissolve, dislodge
and foam to the surface from easy removal of dirt, oil, grease and scum.
AC-3 Cleaner removes cement drippings and waste from new surfaces. It will also clean and renew old weathered and stained concrete and masonry buildings
and prepare the surface to receive weather proof treatment or paint.
AC-3 will remove efflorescence, dirt and rust stains from concrete, ceramic tile, terrazzo, marble, slate, stone and porcelain bath fixtures.
AC-3 may also be used on metal surfaces to remove grease, dirt and oil. Cuts size coating and film. Brightens and cleans off oxidation. Etches and cleans concrete floors for painting.
Since AC-3 contains acid and other strong cleaning agents, it should be used with care. Protect eyes, skin and surrounding areas. User should make a test sample, allowing it to dry thoroughly to determine it’s suitability for job conditions and requirements.
From most surfaces and job conditions AC-3 should be diluted with 1 to 10 parts of water. Always use the mildest solution that can do the job. Tough stains and hardened mortar may require full strength.
First dampen surface with water. Apply AC-3 at proper strength to surface and agitate or scrub with nylon or other acid resistant brush for 2 or 3 minutes
or until bubbling action stops. Rinse with clean water, agitate while rinsing. Do not do too large and area at one time, so that the loosened dirt may allowed to settle back or dry. Repeat cleaning operation on stubborn stains as required.
Allow all surfaces to dry before waxing, painting or sealing. Terrazzo must be waxed or sealed as soon as dry.
When clenaing walls start at the bottom and work upward. One gallon cleans approximately 300 sq. ft., depending on porosity and job conditions.
Epoxy Adhesives consists for a wide range of special 100% solids Epoxy Resins/Activator formulations. Each one is designed to perform definite adhesive functions that are ideally suited for high pressure injection grouting. Epoxy Adhesive MV is of medium viscosity for general purpose work. LV is low viscosity for hair line crack sealing. HV is heavy viscosity for wide crack use. These products are resistant to water, moisture and most chemicals. When fully cured, its adhesion, cohesion, compressive, and tensile strength is many time greater that the highest grade concrete available, which makes it highly suitable to reunite and repair structural cracks and voids caused by foundation settlement, over loading, wear and building movement. Epoxy Adhesive will grout and seal crack and voids in concrete and masonry, to repair, rebond and weld structural units and surfaces together, fast and economically.